Pump Shaft Seal 5/8 Buna Carbon Version of PS-200 made by U.S. Seal PS-3960 INSTALLATION INSTRUCTIONS FOR REPLACEMENT SEALS Disassemble pump cavity to expose defective seal. Removal of old seal and installation of new seal requires careful operations and precautions. CAUTION: Lapped and polished faces of new seal are easily scratched and damaged. PROTECT FROM DAMAGE, DIRT and FINGER PRINTS. Carefully remove old seal head and seat taking care not to scratch shalt or seat counterbore. NOTE HOW OLD SEAL IS ASSEIVIBLED. BE SURE REPLACE MENT SEAL IS INSTALLED IN IDENTICAL MANNER. Clean shaft and counterbore surfaces using fine emery cloth or equivalent Remove rust, burrs, and wipe clean. Shaft, seat counterbore and rubber members of seal head and seat should be lubricated with a lubricant compatible with the seal elastomers. U.S SEALUBE is recommended and available from US Seal. U.S. SEALUBE is a WATER BASED formula specifically designed to lubricate rubber making the installation of mechanical seals fast and easy. It provides a high degree of lubricity to all rubber components. It maintains its wetness for a short period of time allowing for easy installation of a mechanical seal. NEVER use PTFE or SILICONE based lubricants. Check seal surfaces
…read more

Pump Motor Cover Noise Reducer made by Afras ABF100 10100 REDUCES SOUND POLLUTION & PROTECTS PUMP MOTOR FROM ENVIRONMENT Required space area for installation: 15″ x 15 ” FEATURES: Fully insulated UV resistant, high temperature thermoplastic with flame retardant foam. No tools required for assembly and disassembly Properly vented for cooling and heat dissipation with knockout sections provided for additional ventilation. Pre-cut parts and knockout sections to fit your needs Designed to enclose the motor and or pump wet end section. Packaging: 2 End Plates (1 precut) 3 Enclosure Plates (2 with precut square vents and one without vent cut out) 1 cover plate. 3 Clips Assembly Instruction Assembly: Motor Enclosure With end plate in upright position (flat edge at bottom) Insert locking sections of the end plates into the slot of the enclosure plates with precut vents located at bottom (Fig. 2). Press down the end plate until it bottoms down and corners are at the same level. Install End plate (precut) with cut towards bottom (Fig.1). Position enclosure plate panel (Fig. 2) (without vents) and press down until locking pins are fully extended through the slot. This will form the roof section. Install SunMuf with cut straddling the
…read more

1/8 in. T-Wrench made by PoolTool 114 Versatile, fits all 1/8 in.s. Large handle for excellent leverage. Will not cause damage to impeller vanes as would be caused by using a screwdriver to turn impeller. Made of durable stainless steel and polypropylene for years of service.

Anthony Apollo Tank 20 in. Clamp with Nut made by Val-Pak V34-133 Used on the following models VA-52, VA-52-2”

Pentair Chalanger Pump Housing 355302 355468 made by CMP 25357-004-000

117Motor Bearing Puller made by PoolTool 117 Easily removes the most stubborn bearings The unique design allows the puller fingers to fit behind all swimming pool motor bearings. Made in U.S.

Anthony Apollo Tank 18 in. Clamp with Nut made by Val-Pak V34-132 Used on the following models VA-26, VA-32, VA-38

Housing Power-Flo Pump made by Hayward SPX1500AA

Sta-Rite LT Series Pump Shaft Seal made by Pentair U109-68SS Used on the following models: LT1/6L LTACL LTADL LTAYDRL For more information check the following link: Sta-RiteLTSeries Centrifugal Pumps Owner’s Manual

Pool Motor Cover Universal made by Blue Devil B8200C Fits all motors from 1/3 HP to 2 HP Shields and protects outdoor motors from sun, rain and dust Assembles in minutes No tool required for assembly Made of heavy duty plastic for long life and durability Heat resistant white top and attractive blue sides Sturdy will not fade from sun or ultraviolet rays