DURA-GLAS and MAX-E-GLAS CENTRIFUGAL PUMPS with TRAP Failure to pump Reduced capacity or discharge pressure Suction leaks/lost prime: Pump must be primed; make sure that pump volute and trap are full of water. Make sure there are no leaks in suction piping. Make sure suction pipe inlet is well below the water level to prevent pump from sucking air. If suction trap gasket is defective, replace it. Suction lift of 15 to 25 feet (4.5 to 7.5 meters) will reduce performance. Suction lift of more than 25 feet (7.5 meters) will prevent pumping and cause pump to lose prime. In either case, move pump closure (vertically) to water source. Make sure suction pipe is large enough. Clogged pipe/trap/impeller, worn impeller: Make sure suction trap is not clogged; if it is, clean trap and strainer. Make sure impeller is not clogged, check impeller for clogging Impeller and diffuser may be worn. If so, order replacement parts from Repair Parts List Pump may be trying to push too high a column of water. If so, a “higher head” pump is needed. Electrical: Pump may be running too slowly; check voltage at motor terminals and at meter while pump is running. If low,
…read more

Diffuser for Sta-Rite Max-E-Glas Dura-Glas 3/4-2 HP Full Rated Pump C1-200PA V26-367 CMP purt number is 25356-100-000

Lid Opener for Sta-Rite Max-E-Glas Dura-Glas Pump U79-11

Seal Plate for Sta-Rite Max-E-Glas Dura-Glas Pump C203-193P The kit also includes shaft the seal and the seal plate o-ring.

Diffuser O-ring for Sta-Rite Max-E-Glas Dura-Glas Pump U9-226 V26-368

Lid for Sta-Rite Max-E-Glas Dura-Glas Pump 16920-0011 V26-363 6" Trap

Seal Plate O-Ring for Sta-Rite Max-E-Glas Dura-Glas Pump U9-228 V26-354

Tank Body for Sta-Rite Max-E-Glas Dura-Glas Pump C176-47P1

Lid O-ring for Sta-Rite Max-E-Glas Dura-Glas Pump 16920-0012 V26-366 6" Trap

Shaft Seal for Sta-Rite Max-E-Glas Dura-Glas Pump 17304-0100S PS-200 INSTALLATION INSTRUCTIONS FOR REPLACEMENT SEALS Disassemble pump cavity to expose defective seal. Removal of old seal and installation of new seal requires careful operations and precautions. CAUTION: Lapped and polished faces of new seal are easily scratched and damaged. PROTECT FROM DAMAGE, DIRT and FINGER PRINTS. Carefully remove old seal head and seat taking care not to scratch shalt or seat counterbore. NOTE HOW OLD SEAL IS ASSEIVIBLED. BE SURE REPLACE MENT SEAL IS INSTALLED IN IDENTICAL MANNER. Clean shaft and counterbore surfaces using fine emery cloth or equivalent Remove rust, burrs, and wipe clean. Shaft, seat counterbore and rubber members of seal head and seat should be lubricated with a lubricant compatible with the seal elastomers. U.S SEALUBE is recommended and available from US Seal. U.S. SEALUBE is a WATER BASED formula specifically designed to lubricate rubber making the installation of mechanical seals fast and easy. It provides a high degree of lubricity to all rubber components. It maintains its wetness for a short period of time allowing for easy installation of a mechanical seal. NEVER use PTFE or SILICONE based lubricants. Check seal surfaces to be sure they are
…read more