Pentair Temperature Sensor Linear TS5L Temperature Sensor used with Comswimming pool swimming pool and spa control systems. This Sensor May be used for Water or Solar. With the Cp3800 Control system family it may also be used for freeze protection. The UY wire connectors are for 22-26 guage wires and desighned for indoor or outdoor use. For Installation Guide click here.

Jandy SpaLink RS 8 Function Spa Side Remote 150 ft. Black Control 7888 Control filter pump, heater, solar, spa and 7 auxiliary circuits. Remotes are designed to be installed above water level in the spa tile line, decking, or anywhere outdoors in conjunction with any model AquaLinkRS. Works with AquaLink Touch OneTouch All Button user interfaces. 8 Function, spa-side remote with control of spa and 7 auxiliary circuits designed to be installed in spa tile line, decking or anywhere outdoors in conjunction with any model AquaLink RS OneTouch or All Button system. Each SpaLink RS is packaged with a matching flush mount frame and is available in gray, black, and off-white. Also, available separately is a mud box for flush mount installation in the spa tile line. Weather-resistant housing Comes with matching flush mount frame Spa side control of spa and 7 auxiliary circuits Spa side control of desired water temperature Large, easy-to-read display of water and air temperatures Custom labeling of equipment Install up to 3 SpaLink RSs on 1 AquaLink RS OneTouch or All Button system Dimensions: 6 1/2x 2 9/16x 1(L x W x H) Dimensions with frame: 7 1/2x 3 1/2x 1 1/4(L x W x
…read more

Jandy Ji, AquaLink to PDA Wireless Conversion Kit PDACONVJ Move up to AquaLink RS power with the Conversion Kit.. Simply convert your old AquaLink, Ji Series controls to the latest and greatest PDA. No indoor rewiring is required! Features: Simpler programming and control of filter pump, spa switch-over, swimming pool and spa heater, solar and up to 8 auxiliary circuits An attractively styled, sleek and compact indoor control panel or wireless remote Display of water and air temperatures Custom software and decal labeling of all functions Infinite program back-up for power outages Automatic equipment safety circuits and freeze protection Ji2000, Ji4000, Ji8000, AquaLink 2, AquaLink 4, AquaLink 8 To PDA Also includes:

Hayward Temperature Sensor 10K GLX-PC-12-KIT Includes: 1-Hose Clamp 1-Sensor, 10K, Combo, 15ft

Tubing Connector 1/4 in. Tubing to MNPT made by Rola-Chem 550026

Hayward Wireless Spa Side Remote Control AQL2-SS-RF Used with OnCommand ONCOM-ACT-RC

Jandy SpaLink RS 8 Function Spa Side Remote 150 ft. Gray Control 7887 Control filter pump, heater, solar, spa and 7 auxiliary circuits. Remotes are designed to be installed above water level in the spa tile line, decking, or anywhere outdoors in conjunction with any model AquaLinkRS. Works with AquaLink Touch OneTouch All Button user interfaces. 8 Function, spa-side remote with control of spa and 7 auxiliary circuits designed to be installed in spa tile line, decking or anywhere outdoors in conjunction with any model AquaLink RS OneTouch or All Button system. Each SpaLink RS is packaged with a matching flush mount frame and is available in gray, black, and off-white. Also, available separately is a mud box for flush mount installation in the spa tile line. Weather-resistant housing Comes with matching flush mount frame Spa side control of spa and 7 auxiliary circuits Spa side control of desired water temperature Large, easy-to-read display of water and air temperatures Custom labeling of equipment Install up to 3 SpaLink RSs on 1 AquaLink RS OneTouch or All Button system Dimensions: 6 1/2x 2 9/16x 1(L x W x H) Dimensions with frame: 7 1/2x 3 1/2x 1 1/4(L x W x
…read more

Jandy Temperature 1K Sensor 4 Wire Replacement Kit for Ji/AquaLink 4019 Installation Instructions Turn off all power to the Power Center and make sure the pump is not circulating. The location of the water temperature sensor is between the pump and the filter (see Figure below). Drill a 3/8" hole on top of the pipe between the pump and the filter. Insert the Water Temperature Sensor in the hole drilled in step 2. Use the clamp provided in the kit to keep the sensor in place. Run the Sensor’s wire back to the Power Center. Inside the Power Center, remove the screws holding the PCB. Run the Water Temperature Sensor wire through a knockout in the bottom of the Power Center. Plug the connector into the WATER TEMP. SENSOR socket on the PCB. Use the wiring diagram on the inside of the door panel to locate the WATER TEMP. SENSOR socket. Replace the PCB Panel and the Dead Front Panel being careful not to pinch any wires. Restore power to the Power Center. Test the Water Temperature Sensor by turning the pump on and looking at the temperature display on the JI Series Control Panel.

Jandy AquaLink RS TouchLink Desktop Wireless Control TCHLNK-RF Start by selecting the AquaLinkRS Control System that is right for you. Jandycontrols offer more features, styles and peace of mind than other control systems. AquaLink RS monitors your water temperature, activates your water features, sets temperatures and protects your equipment so you can concentrate on relaxing! We offer a control system for virtually every swimming pool and spa configuration and have a number of unique features designed to ensure your swimming pool and spa experience is a pleasure. Introducing Jandy’s new AquaLinkTouch designed with the style and features today’s consumers demand in a technologically advanced controller. AquaLink Touch’s smart, intuitive user interface, customizable features and attractive styling present the best touch panel experience for the swimming pool industry today. Automates any swimming pool or swimming pool and spa combination systems that share equipment, dual equipment systems that share a heater. Variable speed pump interface and control, smart color lighting logic, plus chlorinator option that purifies swimming pools up to 40,000 gallons. TouchLinkFeatures: 7″ diagonal, full color touch panel Digital Picture Frame and slideshow settings from Memory Flash Card input Custom home screen for simplified operation Simple programming and control of filter,
…read more

Hayward Base Station AQL2-BASE-RF required if using AQL2-SS-RF The AQL2-BASE-RF base station must be installed if the AQL2-SS-RF or AQL2-POD will be used. To install the base station, remove the knockout on the upper left side of the OnCommand main control unit, insert the base station, and then tighten the nut from the inside. Included with ONCOM-ACT-RC