Aqua-Flo Dominator Pump Shaft Screw 99730000 V40-401
1:03 am
Aqua-Flo Dominator Pump Shaft Screw 1/4″-20 x 5/16″ 99730000 V40-401
1:03 am
Aqua-Flo Dominator Pump Shaft Screw 1/4″-20 x 5/16″ 99730000 V40-401
1:03 am
Aqua-Flo A-Series Pump Shaft Screw 1/4"-20 x 5/16" 99730000 V40-401
1:03 am
Aqua Flo Dominator Pump Diagram PRIMING PUMP At initial start-up, pump must be primed by filling hair and lint trap with water. To prime pump, remove cover from hair and lint trap: fill pump and suction trap with water. Replace cover (make sure the O-ring is in place) and tighten lock ring. Pump will now prime, with priming time depending upon lift and horizontal distance of suction piping. CAUTION: Do not remove hair and lint strainer lid while pump is running or under pressure! Lid is held in place by a lock ring which can be removed or tightened by hand. Basket must be kept clear of leaves and debris at all times. REMOVING BASKET Turn off motor. Remove lock ring by rotating counter clockwise. DO NOT USE TOOLS. Remove lid. Remove basket and empty debris. Replace basket, fill with water, replace lid and lock ring securely to prevent air from entering and tighten. DO NOT USE TOOLS. Turn on motor Open air-relief valve on top of filter until steady stream of water comes out. NOTE: If pump is installed below water level of swimming pool, close return and suction lines prior to opening hair and lint pot. Make sure
…read more
1:03 am
Aqua Flo A Series Pump Diagram PRIMING PUMP At initial start-up, pump must be primed by filling hair and lint trap with water. To prime pump, remove cover from hair and lint trap: fill pump and suction trap with water. Replace cover (make sure the o-ring is in place) and tighten lock handles. Pump will now prime, with priming time depending upon lift and horizontal distance of suction piping. CAUTION: Do not remove hair and lint strainer lid while pump is running or under pressure! Lid is held in place by lock handles which can be removed or tightened by hand. Basket must be kept clear of leaves and debris at all times. REMOVING BASKET Turn off motor. Remove lid. Remove basket and empty debris. Replace basket, fill with water, replace lid securely to prevent air from entering and tighten. DO NOT USE TOOLS. Turn on motor. Open air-relief valve on top of filter until steady stream of water comes out. NOTE: If pump is installed below water level of swimming pool, close return and suction lines prior to opening hair and lint pot. Make sure to re-open valves prior to operating. DO NOT RUN PUMP DRY! Always maintain proper
…read more
1:03 am
Polaris Booster Pump The Polaris Booster Pump supplies pressure water to the Polaris swimming pool cleaner to optimize cleaner efficiency. The Pumpis not self-priming and should only be used when the swimming pool filtration pump is on. Running the booster pump without filtration pump will damage the booster pump. Improper operation of the booster pump will oid the warranty. 1 P5 Volute (Includes Drain Plug) 2 P15 Impeller 3 P55 Seal 4 P95 Bracket O-Ring 5 P10 Bracket 6 P35 Bolt, Stainless, Bracket to Motor 7 P40 O-Ring for Shaft 8 B121 Polaris Booster Pump Motor 0.75 HP P61 Motor, ¾ HP, Threaded Shaft, 60 Hz 9 P25 Bolt/Nut, Stainless for Volute to Bracket 10 P80 Rubber Strip, Motor/Bracket 11 P70 Pump Stand with Feet, Strip 12 P75 Rubber Feet 13 P65 Bolt, SS, Stand to Bracket and Motor 14 P20 1⁄8" NPTM Plug, Plastic 15 P17 Installation Kit, Softube Quick Connects 16 P19 Pump Hose, 6 ft., Flexible Reinforced 17 P133 Softube Quick Connect 18 P21 Pump Quick Connect Retainer • V40-401 Shaft Screw • V40-116 Shaft • B05 V32-606 Pressure Hose 2 ft • HPF8C Booster Pump Polaris Hose to
…read more
1:03 am
Shaft 1/4"-20 x 5/16" Screw for Polaris Booster Pump V40-401
1:03 am
A.O. Smith Centurion 1081 Standard C-Frame Keyed Motor 3/4 HP B121 HP 3/4 RPM 3600 Volts 230/115 Frame 56C Phase 1 Encl Open To use the A.O. Smith Centurion 1081 B121 as a replacement motor for a Polaris Booster Pump You have to use with it Polaris Booster Pump Shaft Screws (3) Polaris Booster Pump Shaft Extention